FabFilter Twin 2 Help
Drag-and-drop modulation slots
The XLFO is like a classic LFO but it can do so much more! It can also be used as a 16 step sequencer with an individual glide parameter for every step. The display shows the waveform that is used by the XLFO. Steps can be freely added or deleted to shape the funkiest of waveforms. But there is more... This XLFO can also be used as arpeggiator! The values can be equally be distributed over 2 octaves, so when connecting it to any pitch parameter, it will function like an arpeggiator. We couldn't make it more funky! (Any suggestions? Please let us know.)
To add an XLFO as a modulation source, click the + button in the source selection bar and click New XLFO.
At the left of the XLFO interface, you find the global parameters that affect the entire waveform:
The frequency knob sets the time it takes for 1 cycle of the waveform to complete. This knob is a modulation target, so you could let one XLFO modulate the frequency of another XLFO. The XLFO can be synchronized to the tempo of the plug-in host or set to run free. With the options at the top-right corner of the frequency button you can choose the different settings:
When using any of the synchronized cycle lengths (16 to 1/64, measured in bars) the frequency knob changes into the Offset knob. It now acts like a cycle length multiplier and therefore is capable of changing the cycle length relative to the host tempo, from half to two times the host tempo. Click the dots around the knob to jump to certain predefined offsets for dotted and triplet synchronization. Note: the Offset parameter is not a modulation target, but you can modulate the Phase offset instead.
Balance
The outer ring of the frequency knob adjusts the time balance of the first and last halves of
the step sequence. For example, when turned to the left, the first half of the wave form is
generated more quickly than the last half.
MIDI sync
The XLFO can be restarted at any point using MIDI if the MIDI sync option is enabled at the
top-right corner of the frequency knob. When activated a note-on MIDI message (e.g. pressing
a key) will restart the cycle of the waveform (to the point set by the Phase offset
slider).
Snap
This function makes it possible to use the XLFO as an arpeggiator. When you enable Snap, a
small piano keyboard appears, the range of the XLFO turns into 2 octaves, and steps "snap" to
notes on the piano keyboard. Now when you modulate the oscillator detune, master tune, or
filter frequency, turn the slot level to maximum, and the total amount of modulation will
exactly correspond to 2 octaves. If you modulate a detune
knob, it will sound like a classic arpeggiator. With filter
frequency parameters, you will hear individual notes if used with high filter peak
settings.
Glide
The global Glide knob acts like an overall glide offset. The amount of glide determines the
point within a step at which the XLFO starts to interpolate to the value of the next step.
The global Glide value is added to the glide value for individual steps to arrive at the
final glide value for each step. The final glide value is limited between 0 (no
interpolation) and 1 (full interpolation). Because the global Glide value can range from -1
to 1 it can completely overrule the individual step glide values at the extreme settings. It
is also a modulation target which allows for very cool effects.
Phase offset
In the step editor you can see a triangular shape. The vertical line of the shape indicates
the beginning of each cycle. You can move this triangular shape, and thus change the
beginning of a XLFO cycle. This phase offset is a modulation target, so when the XLFO
frequency is set to 0, you can use another modulator to cycle through the different
steps.
Tip: Like with knobs, you can
Ctrl/Command-click on the phase offset slider to reset it.
At the top right of the global settings, the Presets button provides access to the XLFO section presets. The Remove button
deletes the XLFO source. By default, the XLFO
starts with two steps that make a sine wave. You can customize this by overwriting the predefined
Default section preset.
You can shape the waveform of the XLFO in almost any way you want by editing the individual steps.
If one or more steps are selected, the XLFO expands to show the step interface where the parameters for the selected steps can be edited:
The Value knob adjusts the value of step. This is the same as dragging the step up and down, except that with multiple selected steps, the value of all steps is set to the same value. In contrast, when you drag multiple selected steps, the relative distance is kept the same.
The Glide knob sets the per-step glide value. This is combined with the global glide value to determine at which point the XLFO starts to interpolate towards the next step.
To start exploring the many sound shaping possibilities start with a XLFO that modulates a Filter Frequency knob to make the sound change over time. You'll be amazed by the many possibilities. Have a look at the presets to see the XLFO in many different setups to get an idea of what it can do for you and start creating your own sequences to funkify your life!
Next: Envelope generator
See Also
Modulation
Drag-and-drop modulation slots
What-you-use-is-what-you-see